# Inductor Parameters & Specifications

### When selecting inductors it is necessary to understand the parameters and specifications found in the datasheet.

**Inductors Includes:**

Inductor types
Specifications
How to select the right inductor
Ferrites
Ferrite beads

Like any electronic component, there are several parameters and specifications that are associated with inductors.

The inductor parameters and specifications enable the component to be satisfactorily described and correctly used within the circuit.

The various parameters that can be used enable the inductor performance to be fully specified so that it can confidently used within the required circuit.

## Inductance

The key parameter for any inductor is its inductance. The inductance is the property of the inductor that tends to oppose any change in the current flowing.

The SI unit of inductance is the henry, H. The inductance of a circuit is one henry if the rate of change of current in a circuit is one ampere per second and this results in an electromotive force of one volt.

The actual level of the inductance is influenced by many factors including the number of turns on the coil, coil diameter and in particular the core used within the coil.

As a one henry coil would be very large and only used in very low frequency applications, inductor parameters are more normally specified in terms of microhenries,, µH. Other values may also be used and can be converted according to the table below:

Value | Value in terms of microhenries |
---|---|

1 henry | 1 000 000 µH |

1 millihenry | 1 000 µH |

1 nanohenry | 0.001µH |

## DC Resistance

Another important inductor parameter is the DC resistance it exhibits. As inductors are often manufactured from very thin wire, the DC resistance can sometimes be significant. Even when thicker wire is used, it is still an important factor because it can significantly affect the overall performance as an inductor.

The DC resistance can be considered to be in series with the pure indictor for the sake of most circuit simulations, although in reality it is distributed throughout the inductor.

The DC resistance, measured with a steady current is normally specified in Ohms, Ω and typically given as a maximum value as it is sometimes difficult to control accurately.

## Saturation Current

The saturation current is another parameter or specification which is of importance for an inductor.

In an inductor it is possible to saturate the core because there is a limit to the level of magnetic flux a magnetic core such as iron, ferrite or another compound can take. When this occurs the relative permeability falls and in turn this causes the level of inductance falls.

The saturation current is generally taken to be the current at which the level of inductance falls by a specified amount. Figures of 10% are often used for inductors with ferrite cores and 20% for those with iron powdered cores.

## Incremental current

Often inductors run with a bias current passing through them. For example, this may be the quiescent current for a transistor collector where the inductor is in the collector circuit itself. There is a drop in inductance that is caused by this current and it is necessary to understand this so that the circuit will be able to operate satisfactorily even when the DC bias current is flowing.

The incremental current inductor parameter is generally taken as the DC bias current flowing through the inductor that causes the inductance to fall by 5% from its initial value with zero bias.

The value for the incremental current parameter or specification indicates the level where a further increase in current would cause the inductance to fall by a significant value.

The incremental current value for an inductor is most important when using ferrite cores as they exhibit a much faster reduction in inductance with increasing current than other forms of core such as a powered iron core.

## Rated current

Another important inductor parameter is the rated current. This specification is the maximum continuous current that the inductor can withstand. Generally the limiting factor for this parameter is the temperature rise of the inductor.

With thin wire being used in many inductors to keep the size to a minimum, the current flow can result in power being dissipated in the inductor with the result that the temperature rises. Undue temperature rises can reduce the reliability or even cause catastrophic failure in some circumstances.

## Core permeability

The permeability of the inductor core is a key parameter. It governs the inductance of the inductor for a given inductor geometry. Higher permeability core materials result in the inductor providing a higher level of inductance.

The core material as well as the core shape, size and geometry affect the overall effective permeability, and therefore these factors also need to be taken into consideration as well.

## Winding self-capacitance

The inductor self-capacitance or distributed capacitance is a particularly important parameter in many applications. It arises from the fact that apart from adding inductance, the wires also have a small but appreciable level of capacitance between each other.

The diagram shows individual capacitors within the inductor as this a simplified way of showing the self-capacitance. However the capacitance is distributed throughout the whole inductor and it is not separate capacitance.

The level of capacitance depends on the area of the wire, the distance between the two wires and the permittivity of the material between them. Normally the level is relatively low, but it manifests itself to an external circuit as a small amount of capacitance across the inductor. This gives rise to what is termed the self-resonant frequency of the inductor.

## Self resonant frequency

In view of the self-capacitance or distributed capacitance, the inductor forms a parallel resonant circuit as shown.

At the point where the inductor resonates the inductive reactance and the capacitive reactance will cancel each other out, and the overall impedance of the circuit will fall to a value governed by the DC resistance of the circuit..Below the resonant frequency the inductive reactance will dominate, whereas above the self-resonant frequency the capacitive reactance will dominate.

As a result inductors are normally used below their self-resonant frequency to ensure that the effects of self-resonance are not experienced.

**More Electronic Components:**

Resistors
Capacitors
Inductors
Quartz crystals
Diodes
Transistor
Phototransistor
FET
Memory types
Thyristor
Connectors
RF connectors
Valves / Tubes
Batteries
Switches
Relays
* Return to Components menu . . .*